|
Dynalco M951 Hall Effect Speed Sensor
Dynalco M951霍爾效應速度傳感器
Dynalco Active Powered - Ordinary Area有源磁傳感器 - 普通區域應用
Dynalco Magnetic Pickups Speed Sensors 磁傳感器速度傳感器
該霍爾效應傳感器旨在檢測含鐵材料（齒輪齒，孔或銷），以進行低至零速的速度測量。數字輸出與大多數PLC輸入卡兼容。該傳感器的作用距離很遠（4.500英寸），螺紋為5 / 8-18。This hall effect sensor is designed to sense ferrous material (gear teeth, hole or pin) for speed measurement down to zero-speed. The digital output is compatible with most PLC input cards. This sensor has a long reach (4.500 inches) and a 5/8-18 thread.
Dynalco M951 Hall Effect Speed Sensor 
Dynalco M951 Hall Effect Speed Sensor
M951
M951 - 5/8-18 x 4.5
5/8-18 x 4.5" - 3 Pin
Active (Powered) - Ordinary Area
Zero Speed Hall-Effect Sensors
Datasheets
Dynalco M951 Hall Effect Speed Sensor Datasheet
Miscellaneous
Dynalco Rep Locator
Magnetic Pickup Look-up
Details
M951
M951-5 / 8-18 x 4.5
5 / 8-18 x 4.5“-3針
有源（有源）-普通區域
零速霍爾效應傳感器
數據表
Dynalco M951霍爾效應速度傳感器數據表
雜
Dynalco Rep定位器
磁性傳感器
細節
該霍爾效應傳感器旨在檢測含鐵材料（齒輪齒，孔或銷），以進行低至零速的速度測量。數字輸出與大多數PLC輸入卡兼容。該傳感器的作用距離很遠（4.500英寸），螺紋為5 / 8-18。This hall effect sensor is designed to sense ferrous material (gear teeth, hole or pin) for speed measurement down to zero-speed. The digital output is compatible with most PLC input cards. This sensor has a long reach (4.500 inches) and a 5/8-18 thread.
SPECIFICATIONS:
POWER SUPPLY: 8 TO 32VDC.
SUPPLY CURRENT: 30 mA MAXIMUM
OPERATING TEMPERATURE: -30 F TO +250 F (-35 C to 125 C)
SENSED FREQUENCY: 0 TO 20 KHZ
OUTPUT VOLTAGE: SQUARE WAVE.
LOGIC 0: WHEN NEAR FERROUS MATERIAL, ACTIVATES SENSOR.
* +0.5V AT ≤ 50mA.
LOGIC 1: WHEN NO FERROUS MATERIAL PRESENT
* FOR Vin ≤ 24V USE A PULL UP RESISTOR ≥ 1KΩ
* FOR Vin ≤ 16V USE A PULL UP RESISTOR ≥ 330Ω
INSULATION RESISTANCE: 100 MEGAohm MIN. AT 50 VDC (COMMON TO HOUSING)
HOUSING: 303 STAINLESS STEEL, BLIND END.
規格：
電源：8至32VDC。
電源電流：30 mA
工作溫度：-30 F至+250 F（-35 C至125 C）
感應頻率：0至20 KHZ
輸出電壓：方波。
邏輯0：當靠近鐵質材料時，激活傳感器。
* + 0.5V AT≤50mA。
邏輯1：當沒有含鐵材料PRESENT
*于VIN≤24V USE上拉電阻器≥1KΩ
*于VIN≤16V USE一個上拉電阻≥330Ω
絕緣電阻：100兆歐。50 VDC時（常見于外殼）
外殼：303不銹鋼，盲端。
|
